|

Embedded Software Solutions
|
|
Flasher / In-Circuit Programmer
In-circuit-programmers easily integrated into any production environment
SEGGER's in-circuit flash programming solutions are ultra-fast and reliable, making them the perfect choice for mass production environments. The portfolio includes devices specialised for service environments and prototype programming.
|
Programmers for Legacy Devices
In-Circuit-Programmer for M16C, M32C, R8C, R32C, M38000, ST7 and ST9 series of flash microcontrollers.
|
|
|
|
Flasher ATE is perfectly suited for high volume mass production environments. The modular system uses a communication main board at its heart, that distributes the commands received from an ATE, ICT or a similar automated production handler system to the programming modules. Each programming module can be set up with individual configurations and firmware. The Gang Programmer is capable to program multiple devices in parallel, whether these devices are equal or part of a multi-device system, Flasher ATE can handle all production setups.
Main features
- In-System Programmer (ISP)
- Ultra fast programming
- Control interfaces for ATEs and similar production process handlers
- Switchable target power
- J-Flash for an easy setup
- Scalable solution with up to 10 individual channels
- Parallel channels, no demultiplexing required
- Galvanic isolation of each module
- Target supply voltage may be up to 15V
- Gang ProgrammingMore Information
|
|
|
Flasher Secure is a mass production programming system, capable of protecting the vendor's IP regardless of the production site. It provides full control over the programming process at contract manufacturers (CM) and similar environments.
Main features
- Authenticated production
- Production volume control
- CM administration and setup portal
- Ultra fast programming
- Support for Cortex-M/R/A, RX, PPC
- Prevents production of counterfeit units
- No overhead in programming time
- Secure your production at contract manufacturersMore Information
|
|
|
Flasher ARM is a programming tool for microcontrollers with on-chip or external Flash memory and ARM7/9/11 or Cortex-M/R/A core. Flasher ARM is designed for programming flash targets with the J-Flash software or stand-alone.
Main features
- Stand-alone JTAG/SWD programmer (Once set up, Flasher can be controlled without the use of PC program)
- Support for ARM7/9/11 and Cortex-M/R/A cores
- Ethernet interface
- No power supply required, powered through USB
More Information
|
|
|
Flasher PRO is a programming tool for microcontrollers with on-chip or external Flash memory and ARM7/9/11, Cortex-M/R/A, RX or PPC core. Flasher PRO is designed for programming flash targets with the J-Flash software or stand-alone.
Main features
- Stand-alone JTAG/SWD programmer (Once set up, Flasher can be controlled without the use of PC program)
- Ethernet interface
- Supports internal and external flash devices
- Wide range of devices are supported
- Free firmware updates
- 128 MB internal NAND flash, used for storing configuration and data files
- Serial in target programming supported
More Information
|
|
|
Flasher STM8 is a programming tool for STM8 series of flash microcontrollers.
Main features
- All STM8 devices can be programmed
- Integrated optical isolation between host and target system
- Full duplex 100 Mbit Ethernet interface
- 128 MB internal flash memory to store target program
More Information
|
|
|
Portable Service Programmers
Handheld Flash Programmer for on-chip and external flash memory. |
|
Flasher Portable PLUS is a programming tool for microcontrollers with on-chip and external Flash memory.
Flasher Portable PLUS has been designed to fill the need of an extremely portable, production grade Flash programmer used for in-field firmware updates. No need to be tethered to an outlet, it is powered by standard batteries. Flasher Portable programs flash targets in stand-alone mode or via J-Flash PC software.
Main features
- Stand-alone in-circuit programmer (Once set up, Flasher can be controlled without the use of a PC program)
- Powered by internal battery, no external power supply required
- Up to 10 hours programming with one battery charge
- Supports having up to eight configurations/data files being stored on Flasher
More Information
|
|
|
Programmers for Legacy Devices
In-Circuit-Programmer for M16C, M32C, R8C, R32C, M38000, ST7 and ST9 series of flash microcontrollers. |
|
Flasher ST7 is a programming tool for ST7 series of flash microcontrollers.
Main features
- Small, compact housing
- Easy to use windows program
- 512 KByte internal Flash memory to store target program
More Information
|
|
|
Flasher 5 PRO is a programming tool for Renesas M16C/62, M16C/80, M32C, M79, R32C, R8C series of microcontrollers. This tool allows programming of MCU via serial synchronous or asynchronous interface in circuit only. A target system is required.
Main features
- Serial (in target) programming supported
- 64 MByte internal Flash memory to store target program
- PC program allows batch mode processing for usage in automated test systems
- Once set up, Flasher can be controlled without the use of a PC program
More Information
|
|
For more information please contact
the MicroWay sales team: |
 |
Head Office
MicroWay Pty Ltd
PO Box 84,
Braeside, Victoria, 3195, Australia
Ph: 1300 553 313
Fax: 1300 132 709
email: sales@microway.com.au
ABN: 56 129 024 825 |
Sydney Sales Office
MicroWay Pty Ltd
PO Box 1733,
Crows Nest, NSW 1585, Australia
Tel: 1300 553 313
Fax: 1300 132 709
email: sales@microway.com.au
ABN: 56 129 024 825 |
New Zealand Sales Office
MicroWay Pty Ltd (NZ)
PO Box 912026
Victoria Street West
Auckland 1142, New Zealand
Tel: 0800 450 168
email: sales@microway.co.nz |
International: call
+61 3 9580 1333, fax +61 3 9580 8995
|
|
|